Forum Turris
Fórum Turris Nápověda

Milí majitelé routerů Turris,

toto fórum bylo 9. 12. 2016 zmrazeno a nahrazeno naším novým Turris fórem. Ještě chvíli bude dostupné k prohlížení, ale již zde není možné přispívat. Více informací naleznete v oznámení o uzavření fóra.


Dear Turris routers users,

this forum has been frozen on Dec 9th, 2016 and replaced by our new Turris forum. It will be read-only accessible for some time after. For more information, read the announcement about closing the forum.

Nahoru Téma Majitelé routerů / Technická podpora / Nefunkcni turris
- - Od David K. Dne 2014-09-11 15:56
myslim ze tu este nikdo podobny problem neprobiral. Co me tizi je to ze nemuzu dostat turris do zadneho pouzitelneho stavu.

Cim to zacalo: rano jsem vstal turris na nic nereagoval, normalni restart nepomohl tzn sel do tovarniho nastaveni

Tovarni nastaveni: vse funguje jak ma dokud nezacnu router nastavovat

Nastaveni "online": zde zacina prvni z nekolika problemu ... pri procesu se u aktualizaci stane chyba ktera blokne www rozhrani nejsem schopen ted vykopirovat chybu (tyka se lighttpd) kazdopadne se moc daleko nedostanu a router je napul mrtvej
Nastaveni "offline": abych predesel failu s aktualizacema rozhodnul sem se to zkouset i bez kabelu kde to sice vsechno nastavim ALE ve chvili kdy se pusti updater sem zpet tam kde sem byl

Pri jakemkoliv restartu mam tak 50% sanci ze to turris prezije v provozu schopnejm stavu tzn klienti na lan/wifi maji internet, obcas prestane fungovat dns/dhcp proste dost random aktualne treba nepignu "nic" od sebe ani z turrise ale fora mi z nejakyho duvodu jdou.
Jednou za cas se stane ze router vubec nebootne.

Pripojoval se nekdo na turris seriovou linkou z win? Jaky soft pouzit?
Nesetkal se nekdo s timto problemem? Pripadne jak ho resil?

Uz sem psal rano mail na podporu bohuzel zatim bez reakce.
Nadřazený - - Od David K. Dne 2014-09-11 19:12
Resil nekdo pripojeni na seriovou linku z win? nejak nemuzu najit soft kterym se tam pripojit... chapu ze by to melo umet putty ale jak mu tam hodit usb to nejak nechapu
Nadřazený - - Od Ondřej Caletka (>>>) Dne 2014-09-11 21:32
V routeru je vestavěn převodník USB2serial, myslím, že od FTDI. Seženete-li příslušný ovladač, začne se turris tvářit jako nový sériový port (např. COM3), na který se z PuTTY připojíte.
Nadřazený - - Od David K. Dne 2014-09-11 22:41 Upraveno 2014-09-12 00:59
dekuji za navedeni nejak me nenapadlo schanet ovladace (pri tech vypadcich mi je win nenasli), kazdopadne teda dalsi problem je ze moje seriova linka vypada takto

teda na prvni pokus coz teda svadim na to ze aktualne je turris v nepouzitelnem stavu (nijak nebootne) ale aspon se v reseni muzu posunout dal

Dekuji
Nadřazený - - Od David K. Dne 2014-09-12 01:00
bohuzel jsem se dal nepohnul... nekdo kdo by poradil s nastavenim v putty?
Nadřazený - - Od Martin Sojka Dne 2014-09-12 12:47
Dobrý den, pod win7 jsem neměl s připojením na sériovou linku žádný problém. Po zapojení se objevilo další zařízení (v mém případě COM34) a v Putty jsem se na něj připojil (rychlost je třeba nastavit na 115200).
Nadřazený - Od David K. Dne 2014-09-12 13:15
Dekuji byl to posledni "drobek" do skladacky (rychlost portu).

no a ze seriove linky jsem zjistil nasledujici:

Pocitam ze me ceka reinstal pomoci karty, tucne jsou zviraznene "chyby" pripadne jestli by to mohl este nekdo okomentovat bylo by to pro me super

U-Boot 2013.10-rc2-gb02fcf4 (Feb 06 2014 - 14:11:35), Build: jenkins-OpenWRT-Turris-MASTER-slaves=ubuntu-openwrt-32

CPU0:  P2020E, Version: 2.1, (0x80ea0021)
Core:  e500, Version: 5.1, (0x80211051)
Clock Configuration:
       CPU0:1200 MHz, CPU1:1200 MHz,
       CCB:600  MHz,
       DDR:400  MHz (800 MT/s data rate) (Asynchronous), LBC:37.500 MHz
L1:    D-cache 32 KiB enabled
       I-cache 32 KiB enabled
Board: TURRIS1 CPLD: V4.1 PCBA: V4.0
Error, wrong i2c adapter 2 max 2 possible
rom_loc: nor upper bank
SD/MMC : 4-bit Mode
eSPI : Enabled
I2C:   Error, wrong i2c adapter 2 max 2 possible
ready
SPI:   ready
DRAM:  Detected UDIMM 9905428-181.A00LF
2 GiB (DDR3, 64-bit, CL=6, ECC off)
Flash: 16 MiB
L2:    512 KiB enabled
NAND:  256 MiB
MMC:  FSL_SDHC: 0
*** Warning - bad CRC, using default environment

PCIe1: Root Complex of mini PCIe SLOT, no link, regs @ 0xffe0a000
PCIe1: Bus 00 - 00
PCIe2: Root Complex of PCIe SLOT, x1, regs @ 0xffe09000
  02:00.0     - 168c:0030 - Network controller
PCIe2: Bus 01 - 02
Error, wrong i2c adapter 2 max 2 possible
In:    serial
Out:   serial
Err:   serial
Net:   Phy not found
PHY reset timed out
eTSEC1, eTSEC2, eTSEC3 [PRIME]
Hit any key to stop autoboot:  0
BOOT NAND

NAND read: device 0 offset 0x0, size 0x100000
1048576 bytes read: OK

Loading from nand0, offset 0x200000
   Image Name:   Linux-3.10.18
   Created:      2014-02-06  13:15:36 UTC
   Image Type:   PowerPC Linux Kernel Image (gzip compressed)
   Data Size:    1823906 Bytes = 1.7 MiB
   Load Address: 00000000
   Entry Point:  00000000
WARNING: adjusting available memory to 30000000
## Booting kernel from Legacy Image at 00200000 ...
   Image Name:   Linux-3.10.18
   Created:      2014-02-06  13:15:36 UTC
   Image Type:   PowerPC Linux Kernel Image (gzip compressed)
   Data Size:    1823906 Bytes = 1.7 MiB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
## Flattened Device Tree blob at 00400000
   Booting using the fdt blob at 0x400000
   Uncompressing Kernel Image ... OK
   Loading Device Tree to 03ffa000, end 03fffbfc ... OK
WARNING: could not find compatible node fsl-usb2-mph or fsl-usb2-dr: FDT_ERR_NOTFOUND.
WARNING: could not find compatible node fsl-usb2-dr: FDT_ERR_NOTFOUND.

[    0.000000] Using P2020 RDB machine description
[    0.000000] Memory CAM mapping: 256/256 Mb, residual: 1536Mb
[    0.000000] Linux version 3.10.18 (beast@ubuntu-openwrt) (gcc version 4.6.4 (OpenWrt/Linaro GCC 4.6-2013.05 r38891) ) #1 SMP Thu Feb 6 14:15:32 CET 2014
[    0.000000] CPU maps initialized for 1 thread per core
[    0.000000] bootconsole [udbg0] enabled
setup_arch: bootmem
mpc85xx_rdb_setup_arch()
[    0.000000] mpc85xx_rdb_setup_arch: Could not find Quicc Engine node
[    0.000000] MPC85xx RDB board from Freescale Semiconductor
arch: exit
[    0.000000] Zone ranges:
[    0.000000]   DMA      [mem 0x00000000-0x1fffffff]
[    0.000000]   Normal   empty
[    0.000000]   HighMem  [mem 0x20000000-0x7fffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00000000-0x7fffffff]
[    0.000000] MMU: Allocated 1088 bytes of context maps for 255 contexts
[    0.000000] PERCPU: Embedded 7 pages/cpu @c13d8000 s6816 r8192 d13664 u32768
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 523264
[    0.000000] Kernel command line: root=/dev/mtdblock8 rw rootfstype=jffs2 console=ttyS0,115200
[    0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Sorting __ex_table...
[    0.000000] Memory: 2010296k/2097152k available (3520k kernel code, 86856k reserved, 156k data, 209k bss, 180k init)
[    0.000000] Kernel virtual memory layout:
[    0.000000]   * 0xfffbf000..0xfffff000  : fixmap
[    0.000000]   * 0xffc00000..0xffe00000  : highmem PTEs
[    0.000000]   * 0xffbfd000..0xffc00000  : early ioremap
[    0.000000]   * 0xe1000000..0xffbfd000  : vmalloc & ioremap
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[    0.000000] Hierarchical RCU implementation.
[    0.000000] NR_IRQS:512 nr_irqs:512 16
[    0.000000] mpic: Setting up MPIC " OpenPIC  " version 1.2 at ffe40000, max 2 CPUs
[    0.000000] mpic: ISU size: 256, shift: 8, mask: ff
[    0.000000] mpic: Initializing for 256 sources
[    0.000000] mpc85xx_rdb_pic_init: Could not find qe-ic node
[    0.000000] clocksource: timebase mult[d555555] shift[24] registered
[    0.006301] pid_max: default: 32768 minimum: 301
[    0.010965] Mount-cache hash table entries: 512
[    0.016955] mpic: requesting IPIs...
[    0.021065] Brought up 2 CPUs
[    0.024534] NET: Registered protocol family 16

[    0.036094] Found FSL PCI host bridge at 0x00000000ffe09000. Firmware bus number: 0->1
[    0.043937] PCI host bridge /pcie@ffe09000 (primary) ranges:
[    0.049583]  MEM 0x00000000a0000000..0x00000000bfffffff -> 0x00000000a0000000
[    0.056797]   IO 0x00000000ffc10000..0x00000000ffc1ffff -> 0x0000000000000000
[    0.063933] /pcie@ffe09000: PCICSRBAR @ 0xfff00000
[    0.068970] Found FSL PCI host bridge at 0x00000000ffe0a000. Firmware bus number: 0->0
[    0.076812] PCI host bridge /pcie@ffe0a000  ranges:
[    0.081676]  MEM 0x0000000080000000..0x000000009fffffff -> 0x0000000080000000
[    0.088889]   IO 0x00000000ffc00000..0x00000000ffc0ffff -> 0x0000000000000000
[    0.096025] /pcie@ffe0a000: PCICSRBAR @ 0xfff00000
[    0.110153] PCI: Probing PCI hardware
[    0.113918] fsl-pci ffe09000.pcie: PCI host bridge to bus 0000:00
[    0.119945] pci_bus 0000:00: root bus resource [io  0x0000-0xffff]
[    0.126103] pci_bus 0000:00: root bus resource [mem 0xa0000000-0xbfffffff]
[    0.132971] pci_bus 0000:00: root bus resource [bus 00-ff]
[    0.138483] pci 0000:00:00.0: ignoring class 0x0b2000 (doesn't match header type 01)
[    0.154208] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
[    0.159524] fsl-pci ffe0a000.pcie: PCI host bridge to bus 0001:02
[    0.165542] pci_bus 0001:02: root bus resource [io  0x20000-0x2ffff] (bus address [0x0000-0xffff])
[    0.174489] pci_bus 0001:02: root bus resource [mem 0x80000000-0x9fffffff]
[    0.181357] pci_bus 0001:02: root bus resource [bus 02-ff]
[    0.186861] pci 0001:02:00.0: ignoring class 0x0b2000 (doesn't match header type 01)
[    0.194729] pci 0001:02:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[    0.202769] pci 0001:02:00.0: PCI bridge to [bus 03-ff]
[    0.208009] pci 0000:00:00.0: BAR 9: can't assign mem pref (size 0x100000)
[    0.214808] pci 0000:01:00.0: BAR 6: assigned [mem 0xa0020000-0xa002ffff pref]
[    0.222017] pci 0000:00:00.0: PCI bridge to [bus 01]
[    0.226972] pci 0000:00:00.0:   bridge window [io  0x0000-0xffff]
[    0.233057] pci 0000:00:00.0:   bridge window [mem 0xa0000000-0xbfffffff]
[    0.239839] pci 0001:02:00.0: PCI bridge to [bus 03]
[    0.244793] pci 0001:02:00.0:   bridge window [io  0x20000-0x2ffff]
[    0.251052] pci 0001:02:00.0:   bridge window [mem 0x80000000-0x9fffffff]
[    0.257831] Some PCI device resources are unassigned, try booting with pci=realloc
[    0.265398] pci 0000:00:00.0: enabling device (0106 -> 0107)
[    0.271049] pci 0001:02:00.0: enabling device (0106 -> 0107)
[    0.279661] bio: create slab <bio-0> at 0
[    0.284740] Switching to clocksource timebase
[    0.290330] NET: Registered protocol family 2
[    0.295034] TCP established hash table entries: 4096 (order: 3, 32768 bytes)
[    0.302049] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[    0.308472] TCP: Hash tables configured (established 4096 bind 4096)
[    0.314830] TCP: reno registered
[    0.318000] UDP hash table entries: 256 (order: 1, 8192 bytes)
[    0.323836] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[    0.330198] NET: Registered protocol family 1
[    0.335665] bounce pool size: 64 pages
[    0.345223] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.350980] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.361159] msgmni has been set to 983
[    0.364895] io scheduler noop registered
[    0.368740] io scheduler deadline registered (default)
[    0.414079] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[    0.422409] serial8250.0: ttyS0 at MMIO 0xffe04500 (irq = 42) is a 16550A
[    0.429144] console [ttyS0] enabled, bootconsole disabled
[    0.429144] console [ttyS0] enabled, bootconsole disabled
[    0.440238] serial8250.0: ttyS1 at MMIO 0xffe04600 (irq = 42) is a 16550A
[    0.447548] ffe04500.serial: ttyS0 at MMIO 0xffe04500 (irq = 42) is a 16550
[    0.454911] ffe04600.serial: ttyS1 at MMIO 0xffe04600 (irq = 42) is a 16550
[    0.463090] ef000000.nor: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x000001 Chip ID 0x002101
[    0.473114] Amd/Fujitsu Extended Query Table at 0x0040
[    0.478282]   Amd/Fujitsu Extended Query version 1.3.
[    0.483340] number of CFI chips: 1
[    0.486964] 6 ofpart partitions found on MTD device ef000000.nor
[    0.492984] Creating 6 MTD partitions on "ef000000.nor":
[    0.498303] 0x000000000000-0x000000020000 : "NOR (RO) DTB Image"
[    0.504826] 0x000000020000-0x0000001c0000 : "NOR (RO) Linux Kernel Image"
[    0.512101] 0x0000001c0000-0x000000340000 : "NOR (RO) JFFS2 Root File System"
[    0.519737] 0x000000340000-0x000000e20000 : "NOR (RO) NAND FW backup"
[    0.526648] 0x000000e40000-0x000000f00000 : "NOR (RW) Cert backup"
[    0.533332] 0x000000f00000-0x000001000000 : "NOR (RO) U-Boot Image"
[    0.545030] ONFI param page 0 valid
[    0.548566] ONFI flash detected
[    0.551748] NAND device: Manufacturer ID: 0x2c, Chip ID: 0xda (Micron MT29F2G08ABAEAWP), 256MiB, page size: 2048, OOB size: 64
[    0.563547] Bad block table found at page 131008, version 0x01
[    0.570093] Bad block table found at page 130944, version 0x01

Nadřazený - - Od David K. Dne 2014-09-12 13:15

[    0.576565] 3 ofpart partitions found on MTD device ff800000.flash
[    0.582753] Creating 3 MTD partitions on "ff800000.flash":
[    0.588243] 0x000000000000-0x000000200000 : "NAND (RW) DTB Image"
[    0.594892] 0x000000200000-0x000000700000 : "NAND (RW) Linux Kernel Image"
[    0.602270] 0x000000700000-0x000010000000 : "NAND (RW) JFFS2 Root File System"
[    0.610084] eLBC NAND device at 0xff800000, bank 1
[    0.615306] fsl_espi ffe07000.spi: master is unqueued, this is deprecated
[    0.622107] fsl_espi ffe07000.spi: at 0xe103c000 (irq = 59)
[    0.628101] ar8216: Module init.
[    0.631798] libphy: Fixed MDIO Bus: probed
[    0.636147] libphy: Freescale PowerQUICC MII Bus: probed
[    0.641802] ar8216: probe addr 0.
[    0.645249] phy_id: 4dd036, ar8xxx_phy_ids: 4dd033
[    0.650302] phy_id: 4dd036, ar8xxx_phy_ids: 4dd034
[    0.655353] phy_id: 4dd036, ar8xxx_phy_ids: 4dd036
[    0.660508] phy_id: 4dd036, ar8xxx_phy_ids: 4dd033
[    0.665560] phy_id: 4dd036, ar8xxx_phy_ids: 4dd034
[    0.670612] phy_id: 4dd036, ar8xxx_phy_ids: 4dd036
[    0.675766] phy_id: 4dd036, ar8xxx_phy_ids: 4dd033
[    0.680818] phy_id: 4dd036, ar8xxx_phy_ids: 4dd034
[    0.685870] phy_id: 4dd036, ar8xxx_phy_ids: 4dd036
[    0.691024] phy_id: 4dd036, ar8xxx_phy_ids: 4dd033
[    0.696076] phy_id: 4dd036, ar8xxx_phy_ids: 4dd034
[    0.701128] phy_id: 4dd036, ar8xxx_phy_ids: 4dd036
[    0.706179] ar8216: gonna list.
[    0.709317] ar8216: after list.
[    0.712455] ar8216: Identifying chip.
[    0.739310] switch0: Atheros AR8327 rev. 2 switch registered on mdio@ffe24520
[    0.746454] ar8216: FOUND!!!.
[    1.962154] fsl-gianfar ffe24000.ethernet eth0: mac: 00:00:00:00:00:00
[    1.968693] fsl-gianfar ffe24000.ethernet eth0: Running with NAPI enabled
[    1.975488] fsl-gianfar ffe24000.ethernet eth0: RX BD ring size for Q[0]: 256
[    1.982628] fsl-gianfar ffe24000.ethernet eth0: TX BD ring size for Q[0]: 256
[    1.990213] fsl-gianfar ffe25000.ethernet eth1: mac: 00:00:00:00:00:00
[    1.996753] fsl-gianfar ffe25000.ethernet eth1: Running with NAPI enabled
[    2.003551] fsl-gianfar ffe25000.ethernet eth1: RX BD ring size for Q[0]: 256
[    2.010693] fsl-gianfar ffe25000.ethernet eth1: TX BD ring size for Q[0]: 256
[    2.018271] fsl-gianfar ffe26000.ethernet eth2: mac: 00:00:00:00:00:00
[    2.024813] fsl-gianfar ffe26000.ethernet eth2: Running with NAPI enabled
[    2.031645] fsl-gianfar ffe26000.ethernet eth2: RX BD ring size for Q[0]: 256
[    2.038787] fsl-gianfar ffe26000.ethernet eth2: TX BD ring size for Q[0]: 256
[    2.046043] ucc_geth_driver: QE UCC Gigabit Ethernet Controller
[    2.052344] i2c /dev entries driver
[    2.056009] mpc-i2c ffe03000.i2c: timeout 1000000 us
[    2.063632] rtc-mcp7940 0-006f: rtc core: registered mcp7940 as rtc0
[    2.070065] mpc-i2c ffe03100.i2c: timeout 1000000 us
[    2.075370] booke_wdt: powerpc book-e watchdog driver loaded
[    2.081402] TCP: cubic registered
[    2.084714] NET: Registered protocol family 17
[    2.089238] Bridge firewalling registered
[    2.093256] 8021q: 802.1Q VLAN Support v1.8
[    2.098894] rtc-mcp7940 0-006f: setting system clock to 2014-09-12 12:01:11 UTC (1410523271)
[    3.910967] jffs2: notice: (1) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[    3.929922] VFS: Mounted root (jffs2 filesystem) on device 31:8.
[    3.936128] Freeing unused kernel memory: 180K (c0343000 - c0370000)
procd: Console is alive
procd: - watchdog -
procd: - preinit -
ifconfig: SIOCSIFFLAGS: Cannot assign requested address
sendto(): Network is unreachable
Press the [f] key and hit [enter] to enter failsafe mode
[    5.456339] usbcore: registered new interface driver usbfs
[    5.461933] usbcore: registered new interface driver hub
[    5.467381] usbcore: registered new device driver usb
[    5.474694] Button Hotplug driver version 0.4.1
[    5.489089] SCSI subsystem initialized
[    5.495449] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    5.502048] fsl-ehci fsl-ehci.0: Freescale On-Chip EHCI Host Controller
[    5.508681] fsl-ehci fsl-ehci.0: new USB bus registered, assigned bus number 1
[    5.515974] fsl-ehci fsl-ehci.0: irq 28, io mem 0xffe22000
[    5.533068] fsl-ehci fsl-ehci.0: USB 2.0 started, EHCI 1.00
[    5.538982] hub 1-0:1.0: USB hub found
[    5.542759] hub 1-0:1.0: 1 port detected
[    5.547262] ehci-platform: EHCI generic platform driver
[    5.557636] sdhci: Secure Digital Host Controller Interface driver
[    5.563836] sdhci: Copyright(c) Pierre Ossman
[    5.568587] sdhci-pltfm: SDHCI platform and OF driver helper
[    5.605046] mmc0: SDHCI controller on ffe2e000.sdhc [ffe2e000.sdhc] using DMA
[    5.616026] usbcore: registered new interface driver usb-storage
[    5.857053] usb 1-1: new high-speed USB device number 2 using fsl-ehci
[    5.993837] hub 1-1:1.0: USB hub found
[    5.997727] hub 1-1:1.0: 2 ports detected
mount_root: mounting /dev/root
ifconfig: SIOCSIFFLAGS: Cannot assign requested address
procd: - early -
procd: - watchdog -
procd: - ubus -
procd: - init -
Please press Enter to activate this console.
[    8.752560] NET: Registered protocol family 10
[    8.763784] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[    8.772820] ip6_tables: (C) 2000-2006 Netfilter Core Team
[    8.787644] Loading modules backported from Linux version master-2013-11-05-0-gafa3093
[    8.795600] Backport generated by backports.git backports-20130802-0-gdb67a3f
[    8.807281] ip_tables: (C) 2000-2006 Netfilter Core Team
[    8.866815] usbcore: registered new interface driver ums-alauda
[    8.873303] usbcore: registered new interface driver ums-cypress
[    8.880053] usbcore: registered new interface driver ums-datafab
[    8.886812] usbcore: registered new interface driver ums-freecom
[    8.893689] usbcore: registered new interface driver ums-isd200
[    8.900413] usbcore: registered new interface driver ums-jumpshot
[    8.907280] usbcore: registered new interface driver ums-karma
[    8.914130] usbcore: registered new interface driver ums-sddr09
[    8.920942] usbcore: registered new interface driver ums-sddr55
[    8.927752] usbcore: registered new interface driver ums-usbat
[    8.938227] xt_time: kernel timezone is -0000
[    8.950965] cfg80211: Calling CRDA to update world regulatory domain
[    8.957628] cfg80211: World regulatory domain updated:
[    8.962795] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[    8.970989] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[    8.978748] cfg80211:   (2457000 KHz - 2482000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[    8.986504] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[    8.994257] cfg80211:   (5170000 KHz - 5250000 KHz @ 80000 KHz), (300 mBi, 2000 mBm)
[    9.002015] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (300 mBi, 2000 mBm)
[    9.009773] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm)
[    9.063924] PPP generic driver version 2.4.2
[    9.068996] NET: Registered protocol family 24
[    9.237712] cfg80211: Calling CRDA for country: US
[    9.242858] cfg80211: Regulatory domain changed to country: US
[    9.248730] cfg80211:  DFS Master region FCC
[    9.252836] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[    9.261198] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
[    9.268996] cfg80211:   (5170000 KHz - 5250000 KHz @ 80000 KHz), (300 mBi, 1700 mBm)
[    9.276753] cfg80211:   (5250000 KHz - 5330000 KHz @ 80000 KHz), (300 mBi, 2400 mBm)
[    9.284506] cfg80211:   (5490000 KHz - 5600000 KHz @ 80000 KHz), (300 mBi, 2400 mBm)
[    9.292259] cfg80211:   (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2400 mBm)
[    9.300012] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (300 mBi, 3000 mBm)
[    9.307763] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm)
[    9.315623] ieee80211 phy0: Atheros AR9300 Rev:3 mem=0xf3540000, irq=24
[   18.326045] ar8216: Module config init.
[   18.330255] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   18.337929] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[   18.345675] IPv6: ADDRCONF(NETDEV_UP): eth2: link is not ready
[   18.885633] ar8216: Module config init.
[   18.889778] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   18.895953] device eth0 entered promiscuous mode
[   18.902512] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[   18.911449] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[   18.917481] device eth1 entered promiscuous mode
[   19.057500] IPv6: ADDRCONF(NETDEV_UP): eth2: link is not ready
[   19.889045] ar8216: config aneg.
[   20.895482] libphy: mdio@ffe24520:00 - Link is Up - 1000/Full
[   20.901332] br-lan: port 1(eth0) entered forwarding state
[   20.906762] br-lan: port 1(eth0) entered forwarding state
[   20.912200] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   20.919539] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[   20.926951] libphy: fixed-0:06 - Link is Up - 1000/Full
[   20.932685] br-lan: port 2(eth1) entered forwarding state
[   20.938115] br-lan: port 2(eth1) entered forwarding state
[   20.943621] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[   22.909040] br-lan: port 1(eth0) entered forwarding state
[   22.941041] br-lan: port 2(eth1) entered forwarding state
procd: - init complete -
procd: Instance log::instance1 s in a crash loop 6 crashes, 0 seconds since last crash


bohuzel sem to musel rozdelit do dvou postu
Nadřazený - - Od Martin Strbačka Dne 2014-09-12 18:34
Dobry den,

Vas log vypada uplne v poradku, chyby ktere jste zvyraznil nejsou podstatne. Pokud zmacknete klavesu enter (po skonceni initu) dostanete shell?
Nadřazený - - Od David K. Dne 2014-09-13 17:20 Upraveno 2014-09-13 17:31
Dobry den,

Ano do shell se dostanu i pres ssh. Uplne zamrznuti turrise se mi nepodarilo zreplikovat bohuzel (myslim ze to bylo ve chvili kdy jsem mountul usb a obnovil moji zalohu ale to ted neresim pac bych radsi vyresil internet na klientech). Ale problem tak nejak pretrvava ve smyslu ze po restartu Turrise ztratim na lan strane pristup do internetu, dhcp, dns normalne funguje odpovida ale nikam se nedostanu viz obrazek



a je jedno zda jde o uprate z nastaveni ci pres auto-update...

Paklize potrebujete nejaky log nebo neco co bych mohl zkusit rad to zkusim bohuzel ted je pro me turris nepouzitelny (ted me napada ze sem mohl hodit aspon cat networku) dodam za chvilku po dalsi "replikaci".

No netwrok je beze zmen stejnej pred i po restartu
Nadřazený - - Od Martin Strbačka Dne 2014-09-15 10:27
Dobry den,

Vezmeme to poporade:
1) Updater Vam ted dobehne korektne?
2) Jak mate v tech Windowsech nastavenou default route?
3) Z turrisu bych rad videl /etc/config/dhcp a /etc/config/firewall pripadne /etc/firewall.user pokud jste do nej neco psal. Pripadne rovnou vystup z prikazu iptables-save.
4) Co vam da prikaz: cat /proc/sys/net/ipv4/ip_forward

Prosim posilejte na muj mail: martin.strbacka@nic.cz

Dekuji.
Nadřazený - Od David K. Dne 2014-09-16 18:51
Dekuji vsem kteri se mi snazili pomoct, problem vyresen
Nadřazený - Od Ondřej Caletka (>>>) Dne 2014-09-12 13:14
To vypadá na špatnou rychlost. Nastavte 115200 8 datových bitů, žádnou paritu a jeden stop bit.
Nahoru Téma Majitelé routerů / Technická podpora / Nefunkcni turris

Powered by mwForum 2.29.3 © 1999-2013 Markus Wichitill